Whelen 7108000 User Manual download pdf (Page 1)

Page 1

ENGINEERING COMPANY INC.

2.60

3.64

MFG

LABEL

-00 (28VDC) Connector Wiring

-50 (14VDC) Connector Wiring

POS 1

POS 2

POS 1

POS 2

(+) 28VDC

(-) GROUND

(+) 14VDC

(-) GROUND

White

Black

Red

Black

(-) GROUND BLACK

20AWG(14VDC) ” ±1.0”

5.5

AWG(28VDC) 12” ±1.0”

(+) 14VDC RED

(+) 28VDC WHITE

18AWG 12” ±1.0”

AWG 5.5” ±1.0”

51 Winthrop Road

Chester, Connecticut 06412-0684

Phone: (860) 526-9504

Fax: (860) 526-2009

Internet: www.whelen.com

Sales/Service e-mail: [email protected]

Aviation

Installation Guide:

Model 71080( )-series

Model(s) 7108000, 7108050

P/N(s):01-0771080-00

01-0771080-50

LED Flashing Anti-Collision

Light Assembly

Form No.14159B (060314)

OPERATING INSTRUCTIONS:

Operational Voltage: . . . . . . . . . 14 / 28 VDC nominal

Average Input Current: . . . . . . . 0.90 / 0.45 Amps

Peak Input Current: . . . . . . . . . . 4.0 / 2.0 Amps @ .3 Seconds

The Model 71080 series LED anti-collision light assembly meets the

requirements of FAR 91.205(c)(3).

EQUIPMENT LIMITATIONS: An approved anti-collision light assembly

should be located so that the light will not impair the crew’s vision or

detract from the conspicuity of the position lights. The baseplate must be

mounted parallel to the vertical and horizontal centerlines of the aircraft

to project the patterns properly.

Certain types of installations may require additional testing.

CONTINUED AIRWORTHINESS: The 71080 series LED anti-collision

light assembly is designed with 8 vertical columns consisting of 4 LEDs

each. Should any one LED or any vertical column fail, the unit must be

repaired or replaced. Inspect the lens and replace if there is excessive

scratching, discoloration or cracking. NOTE: To reduce eye strain, use

an optical filter such as dark glasses or a blue covering dome during

LED inspection.

INSTALLATION PROCEDURES: The following information is to assist

in the installation of a Whelen LED Anti-collision Light System.

1. Using the mounting detail information provided, prepare the aircraft

for means to secure the light assembly.

2. Carefully remove the #4 Phillips screw and lens retainer. Remove

the lens. CAUTION! Do not touch the LEDs with either fingers or

sharp objects. This could soil and/or damage the LED and effect

the optical performance of the LEDs.

3. Connect the light inputs according to the chart shown. Connect the

power lead to an appropriately sized breaker. Connections to be in

accordance with FAA approved methods.

4. Install the light assembly and insure that all leads are clear of any

obstructions and secured as required.

5. Install gasket, lens and lens retainer. Confirm proper gasket fit.

Reinsert screws and tighten firmly.

6. All inverted (bottom) mounted units shall require waterproofing of

the base assembly to the aircraft. NOTE: Drill a 1/8” hole in the

center of the lens for bottom mount units.

7. Check all avionics systems for interference from this installation.

8. A flight check should be performed by a properly certified pilot.

9. Update aircraft records, complete Form 337 and obtain FAA field

approval for installation as required.

MADE IN THE U.S.A.

The conditions and tests required for TSO approval of this article are minimum

performance standards. It is the responsibility of those installing this article either on

or within a specific type or class of aircraft to determine that the aircraft installation

conditions are within the TSO standards. TSO articles must have separate approval

for installation in aircraft. The article may be installed only if performed under 14 CFR

part 43 or the applicable airworthiness requirements.

TSO-C96a

CLASS I, III;

APPROVED

1 2

Aviation 1
4 x #6-32 MTG holes 2

Summary of Contents

Page 1 - Aviation

Page 1®ENGINEERING COMPANY INC.2.603.64MFGLABEL-00 (28VDC) Connector Wiring-50 (14VDC) Connector WiringPOS 1POS 2POS 1POS 2(+) 28VDC(-) GROUND(+) 14VD

Page 2 - 4 x #6-32 MTG holes

Page 2Suggested Mounting Hole Pattern4 x #6-32 MTG holesequally spaced ona 2.170 bolt circle#6-32 Pan Head#6 Lock SpringWasher(typ)1141ITEMPART NUMBE

Related models: 7108050

Comments to this Manuals

No comments

Whelen 7108000 User Manual Page 1

Browse online or download User Manual for Air equipment Whelen 7108000. Whelen 7108000 User Manual

Summary of Contents

Related models: 7108050

Comments to this Manuals

Whelen 7108000 User Manual Page 1

Browse online or download User Manual for Air equipment Whelen 7108000. Whelen 7108000 User Manual

Summary of Contents

Related models: 7108050

Comments to this Manuals

Related products and manuals for Air equipment Whelen 7108000