Whelen 295HFSA7 User Manual download pdf

Page 1

ENGINEERING COMPANY INC.

Automotive: Sirens/Switches

Safety First

This document provides all the necessary information to allow your Whelen product to be properly and safely installed.

Before beginning the installation and/or operation of your new product, the installation technician and operator must

read this manual completely. Important information is contained herein that could prevent serious injury or damage.

• Proper installation of this product requires the installer to have a good understanding of automotive electronics,

systems and procedures.

• Failure to use specified installation parts and/or hardware will void the product warranty!

• If mounting this product requires drilling holes, the installer MUST be sure that no vehicle components or other

vital parts could be damaged by the drilling process. Check both sides of the mounting surface before drilling

begins. Also de-burr any holes and remove any metal shards or remnants. Install grommets into all wire

passage holes.

• If this manual states that this product may be mounted with suction cups, magnets, tape or Velcro®, clean the

mounting surface with a 50/50 mix of isopropyl alcohol and water and dry thoroughly.

• Do not install this product or route any wires in the deployment area of your air bag. Equipment mounted or

located in the air bag deployment area will damage or reduce the effectiveness of the air bag, or become a

projectile that could cause serious personal injury or death. Refer to your vehicle owner’s manual for the air bag

deployment area. The User/Installer assumes full responsibility to determine proper mounting location, based

on providing ultimate safety to all passengers inside the vehicle.

• For this product to operate at optimum efficiency, a good electrical connection to chassis ground must be

made. The recommended procedure requires the product ground wire to be connected directly to the NEGATIVE

(-) battery post.

• If this product uses a remote device to activate or control this product, make sure this control is located in an

area that allows both the vehicle and the control to be operated safely in any driving condition. DO NOT

ATTEMPT TO ACTIVATE OR CONTROL THIS DEVICE IN A HAZARDOUS DRIVING SITUATION.

• It is recommended that these instructions be stored in a safe place and

referred to when performing maintenance and/or reinstallation of this

product.

• FAILURE TO FOLLOW THESE SAFETY PRECAUTIONS AND

INSTRUCTIONS COULD RESULT IN DAMAGE TO THE PRODUCT OR

VEHICLE AND/OR SERIOUS INJURY TO YOU AND YOUR PASSENGERS!

DANGER! Sirens produce extremely loud emergency warning tones! Exposure to these tones without

proper and adequate hearing protection, could cause ear damage and/or hearing loss! The Occupational Safety &

Health Administration (www.osha.gov) provides information necessary to determine safe exposure times in

Occupational Noise Exposure Section 1910.95. Until you have determined the safe exposure times for your

specific application, operators and anyone else in the immediate vicinity should be required to wear an approved

hearing protection device. FAILURE TO FOLLOW THIS RECOMMENDATION COULD CAUSE HEARING LOSS!

CAUTION

Loud siren noise can cause

hearing damage and/or loss.

Refer to OSHA Section 1910.95 prior

to putting ANY siren into service!

Wear

Protection!

ACTIVATION OF THIS

SIREN MAY DAMAGE

UNPROTECTED EARS!

51 Winthrop Road

Chester, Connecticut 06412-0684

Phone: (860) 526-9504

Fax: (860) 526-4078

Internet: www.whelen.com

Sales e-mail: [email protected]

Canadian Sales e-mail: canad[email protected]

Customer Service e-mail: cust[email protected]

For warranty information regarding this product, visit www.whelen.com/warranty

Installation/Operating Guide:

Dual Siren Control Head & Amp

295HFSA7 Flush Mount

295HFSA8 Console Mount

Form No.13946G (053012)

1 2 3 4 5 6 7 8

Summary of Contents

Page 1 - Automotive: Sirens/Switches

Page 1®ENGINEERING COMPANY INC.Automotive: Sirens/SwitchesSafety FirstThis document provides all the necessary information to allow your Whelen produc

Page 2 - Installation: Control Head

Page 2Flush MountSiren Input ConnectorP/N 46-0746511-00Control Head / Flush MountP/N 01-0269919-00Bail Strap MountInstallation KitP/N 01-0463232-00Mou

Page 3 - Installation: Amplifier

Page 3On87654321MainPowerConnectorDipSwitchBankInputHarnessConnectorSiren #1ConnectorSiren #2Connector1. Locate a suitable mounting location for the a

Page 4 - Wiring Diagram

Page 4VEHICLEHORNTOHORNRINGCUTXX3 AMPFUSE20 AMPFUSE(+)Battery(-)BRNGRYORG100 WATTSPEAKER100 WATTSPEAKERORGORGBRNBRNTWO-WAYRADIO SPEAKER(Non-Amplified)

Page 5 - Rotary Switch Operations:

Page 5Rotary Switch Operations:Note: This section assumes the horn ring circuit has been wired asshown on Page 4.RAD (Radio Repeat) - When the rotary

Page 6 - Dip Switch Pos:

Page 6Profile 1 - T3 = Piercer™With the power switch in “Mono” mode, Speakers1&2produce Speaker #1 tones simultaneously.In “Dual” mode, Speakers1&

Page 7

Page 7*MECH = Simulated Mechanical ToneProfile 5 - T3 = Title 13 (Y-249)**Profile 6 - (Title 13 / Mechanical)Profile 7Profile 8RotarySwitchMAN buttonS

Page 8 - Current Draw (AMPS)

Page 8Current Draw (AMPS)Wire GaugeCalculation ChartAll Distances Shown Are In FeetINS. = Insufficient52263INS.INS. INS.INS.INS. INS.INS.INS.INS. INS.

Comments to this Manuals

No comments

Whelen 295HFSA7 User Manual

Browse online or download User Manual for For the car Whelen 295HFSA7. Whelen 295HFSA7 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Whelen 295HFSA7