Whelen 7105500 User Manual download pdf

Page 1

ENGINEERING COMPANY INC.

Aviation

Installation Guide:

Model 71055( ) series

Model 7105500

P/N:01-0771055-00

LED Anti-Collision Light Assembly

Form No.14036C (032114)

OPERATING INSTRUCTIONS:

Nominal Operational Voltage:. . . . . . . . . 14VDC

(Operation from 11V - 16V)

Input Current:

Average: . . . . . . . . . . . . . . . . . . . . . . . . . . 0.75 Amps

Pulse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Amps

Flashrate:. . . . . . . . . . . . . . . . . . . . . . . . . . 45 ±5 FPM

The Model 7105500 LED anti-collision light assembly meets the requirements of

FAR 91.205(c)(3).

EQUIPMENT LIMITATIONS: An approved anti-collision light assembly should be

located so that their light will not impair the crew’s vision or detract from the

conspicuity of the position lights. The baseplate must be mounted parallel to the

vertical and horizontal centerlines of the aircraft to project the patterns properly.

Certain types of installations may require additional testing.

CONTINUED AIRWORTHINESS: The 7105500 LED anti-collision light assembly

is designed with 4 vertical columns consisting of 3 LEDs and 2 vertical columns of

2 LEDs. Should any one LED or any vertical column fail, the unit must be repaired

or replaced. NOTE: To reduce eye strain, use an optical filter such as dark

glasses or a blue covering dome during LED inspection. Inspect the lens and

replace if there is excessive scratching, discoloration or cracking.

INSTALLATION PROCEDURES: The following information is to assist in the

installation of a Whelen LED Anti-collision Light System.

1. Using the mounting detail information provided, prepare the aircraft for

means to secure the light assembly.

2. Carefully remove the #4 Phillips screw and lens retainer. Remove the lens.

CAUTION! Do not touch the LEDs with either fingers or sharp objects. This

could soil and/or damage the LED and effect the optical performance of the

LEDs. Remove the 4 Phillips head screws securing the adapter plate to the

light assembly. Remove the adapter.

3. Using the appropriate hardware, install the adapter plate to the aircraft.

4. Route the wires through the opening in the adapter plate. Connect the light

inputs according to the chart shown. Connect the power lead to an

appropriately sized breaker. Connections to be in accordance with FAA

approved methods.

5. Reinstall the light assembly onto the adapter plate and insure that all leads

are clear of any obstructions and secured as required.

6. Install gasket, lens and lens retainer. Confirm proper gasket fit. Reinsert

screws and tighten firmly.

7. All inverted (bottom) mounted units shall require waterproofing of the base

assembly to the aircraft. NOTE: Drill a 1/8” hole in the center of the lens for

bottom mount units.

8. Check all avionics systems for interference from this installation.

9. A flight check should be performed by a properly certified pilot.

10. Update aircraft records, complete Form 337 and obtain FAA field approval

for installation as necessary.

MADE IN THE U.S.A.

The conditions and tests required for TSO approval of this article are minimum

performance standards. It is the responsibility of those installing this article either on

or within a specific type or class of aircraft to determine that the aircraft installation

conditions are within the TSO standards. TSO articles must have separate approval

for installation in aircraft. The article may be installed only if performed under 14 CFR

part 43 or the applicable airworthiness requirements.

TSO-C96a

CLASS III;

APPROVED

2.60

3.09

ADAPTER

PLATE

MFG

LABEL

(-) GROUND BLACK

18AWG 12” ±1.0”

(+) 14VDC RED

18AWG 12” ±1.0”

51 Winthrop Road

Chester, Connecticut 06412-0684

Phone: (860) 526-9504

Fax: (860) 526-2009

Internet: www.whelen.com

Sales/Service e-mail: [email protected]

1 2

Summary of Contents

Page 1 - Aviation

Page 2 - 100° Countersink

Page 2Suggested Mounting Hole PatternScrew (4-40 X 5/16 PPHMS)P/N:MS51957-1414-0050505-14Washer # Lock Spring MS35338-13516-0050506135(4 )P/N:Washer #

Related models: 7123404 | 7112000 | 7123402 | 7114800 | 7114801 | OR6502RE | 7118400 | 7118401 | 7108040 | 7117001 | 7117002 | 7117007 | 7117008 | 7117009 | 7117010 | 7108019 | 9027701 | 9027702 |

Comments to this Manuals

No comments

Whelen 7105500 User Manual

Browse online or download User Manual for Air equipment Whelen 7105500. Whelen 7105500 User Manual

Summary of Contents

Related models: 7123404 | 7112000 | 7123402 | 7114800 | 7114801 | OR6502RE | 7118400 | 7118401 | 7108040 | 7117001 | 7117002 | 7117007 | 7117008 | 7117009 | 7117010 | 7108019 | 9027701 | 9027702 |

Comments to this Manuals

Related products and manuals for Air equipment Whelen 7105500