Whelen S360DAP User Manual download pdf (Page 3)

Page 3

MANUAL HI/LOW

PHOTOCELL HIGH/LOW

DAY ON - NIGHT OFF

DAY OFF - NIGHT ON

ALTERNATING SYNC

SIMULTANEOUS SYNC

OFF

4 FUNCTION2

OFF

DIP SWITCH VARIABLES

OFF OFFOFFOFF

OFF OFFOFF

OFF OFFONOFF

         

    

         

    

   



Multiple Light Option: Synchronization:

To Run Several Lights in the Synchronized Mode:

Connect your lights as shown in figure 1. With dip switch 3 on, the lights will flash

simultaneously. You may run up to 4 lights at a time.

Interfacing Multiple Units in an Alternating or Simultaneous Flash Pattern:

Connect your lights as shown in figure 2. With dip switch 3 OFF, the 2 lights will blink

alternating. With dip switch 3 on, they will blink simultaneously.

CUSTOMER OPTIONS

Hi/Low Intensity Option:

1. Take the dome and strobe power supply assembly apart

(see “S360D Disassembly Procedure”).

2. Locate the violet (looped) wire, cut it at pin 2 and run it out of

the bottom of the unit with the black and red wires (Fig. 7).

3. Reassemble the unit.

4. Connecting the violet wire to ground will cause the S360D to

operate in high power mode. Removing this wire from

ground forces the S360D into low power mode. A two-

position switch can be installed so that the operator can

easily alternate between high and low power operation (see

“Switch Control Wiring Schematics Chart”).

Flash Pattern Options:

The default flash pattern for the S360D is CometFlash®. You

may choose from several other patterns by making a few simple

changes.

1. First take the unit apart as described under “S360D

Disassembly Procedure”.

2. Now find the input control pigtail assembly in your parts bag,

and plug it in to the extra connector coming out of the strobe

power supply assembly.

3. Next run the brown and white wires out through the center of

the base as shown in Fig. 7.

4. Reassemble the unit and you are ready to choose your

options. IMPORTANT: while re-assembling, make sure you

line up the notch, wire slot and alignment tab (Fig. 3).

To Select SingleFlash: Ground the white wire and tape off the

brown wire.

To Select DoubleFlash: Ground the brown wire and tape off the

white wire.

To Select ActionFlash™: Ground both the white and brown

wires.

  

         

           

     

Fig. 1

Fig. 2

Dip Switch Options:

There are several options you can utilize by changing the dip

switch settings.

Manual High/Low Intensity Mode: You may run your strobe at

either high or low intensity by turning all the dip switches off then

following the instructions under “Hi/Low Intensity”.

Automatic Photocell High/Low Intensity Mode (optional):

The optional Photocell will automatically adjust the intensity of

the strobe light according to the ambient light (darkness switches

the beacon to low power, while daylight switches the beacon to

high power). To engage this function you must turn dip switch 1

on. Then clip the violet wire and tape it off (see “Hi/Low Intensity

Option”). Now the photocell option is always engaged. If you

want to be able to turn this function on or off manually, you must

also attach the violet wire to a switch that will ground or

disconnect it. When you switch to “ground” the light will always be

at high intensity. When you switch to “disconnect” the light will

return to the photocell function.

Photocell Mode (Day On): If you want your strobe to turn on

automatically during the day and off at night, turn dip switch 2 on.

Photocell Mode (Day Off): If you want your strobe to turn off

automatically during the day and on at night, turn dip switch’s 1

and 2 on.

NOTE: Both “C” and “D” are usually used for remote applications.

1 2 3 4 5

Comments to this Manuals

No comments

Whelen S360DAP User Manual Page 3

Comments to this Manuals

Related products and manuals for For the car Whelen S360DAP