Whelen A600PG/PR Series User Manual Page 1

Browse online or download User Manual for Air equipment Whelen A600PG/PR Series. Whelen A600PG/PR Series User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 2
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
Page 1
18 AWG TEFLON
1.79
110°
70°
1.08
.15
1.35
DIA.
1.66
RED(+14or +28VDC)
BLACK(-)GROUND
POS 1 - RED(ANODE)
POS 2 - BLACK(CATHODE)
POS 3 - WHITE(TRIGGER)
TAIL LIGHT WIRES(BLUE)
NO POLARITY
LEAD LENGTH 6.00"±1.00"
2.46
1.83
5.63
.50
1.00
.88
1.75
.140 DIA.
(3) MOUNTING HOLES
FOR #6-32 SCREWS
®
ENGINEERING COMPANY INC.
Aviation
Installation Guide
Model A600PG/PR Series
Wingtip Strobe
Anti-collision/Position
Light Assembly
©2001 Whelen Engineering Company Inc.
Form No.13609B (121410)
Specifications:
Position Lights -
Current Draw................4.0 Amps @ 14 Volts D.C.
2.0 Amps @ 28 Volts D.C.
Weight...........................0.8 lbs.
Length........................... 5.6”
Width............................. 1.7”
Height ........................... 2.4”
INSTALLATION...
The A600 Series must be properly mounted to comply with FAR
Part 91.205(c-2) & (c-3). The light assembly must be mounted so
that the light distribution pattern is not obstructed by any parts of
the aircraft. A limited amount of obstruction is permitted (Ref. FAR
Part 23.1401 for anti-collision lights, and FAR 23.1387 for position
lights).
The baseplate must be mounted parallel to the vertical and
horizontal centerlines of the aircraft to project the patterns
properly.
MOUNTING...
1. If necessary, fabricate the mounting pattern using
dimensions found in fig. 1.
2. Make the necessary wiring connections using 18 gage wire
for the position lights, and Whelen 16 gage 3/c cable for the
strobe lights. All connections must use FAA approved
techniques.
3. Remove the two (6-32 x .312) retainer mounting screws,
retainer and lens.
4. Attach the base assembly to the wingtip using (3) #6-32
countersunk screws (unit may be sealed around periphery
with RTV or equivalent).
5. Re-attach the lens and retainer.
WIRING...
1. The strobe connector should plug into the Whelen interconnecting
cable, or a Whelen strobe power supply.
Observe the following strobe color coding:
PIN 1 - RED (Anode)
PIN 2 - BLACK (Cathode)
PIN 3 - WHITE (Trigger)
Caution: When pins 1 & 2 or pins 2 & 3 are reversed, the system
will appear to operate normally, however this
condition will cause premature flash tube failure.
2. Connect the forward position light wires as follows:
RED - +14 or +28 volts (depending on aircraft voltage)
BLACK - ( - ) Ground
3. The tail position light has no polarity, as noted by both wires being
BLUE. Connect one BLUE wire to +14 or +28 volts (depending on
aircraft voltage). Connect the other BLUE wire to ground (see fig.
2)..
Fig. 1
Fig. 2
For warranty information regarding this product, visit www.whelen.com/warranty
51 Winthrop Road
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Fax: (860) 526-2009
Internet: www.whelen.com
Sales/Service e-mail: aviation@whelen.com
Page view 0
1 2

Summary of Contents

Page 1 - Aviation

Page 118 AWG TEFLON1.79110°70°1.08.151.35DIA.1.66RED(+14or +28VDC)BLACK(-)GROUNDPOS 1 - RED(ANODE)POS 2 - BLACK(CATHODE)POS 3 - WHITE(TRIGGER)TAIL LIG

Page 2

Page 21516 17156212141011813437923ITEMPART NUMBER DESCRIPTIONBASEPLATE ASS’Y (A605)FLASH TUBE ASSEMBLYLAMP, 14V (W1290-14)LAMP, 28V (W1290-28)LENS, GR

Comments to this Manuals

No comments