Whelen 90206 User Manual download pdf (Page 1)

Page 1

ENGINEERING COMPANY INC.

Route 145, Winthrop Road,

Chester, Connecticut 06412

Phone: (860) 526-9504

Fax: (860) 526-2009

Internet: www.whelen.com

Sales/Service e-mail: aviation@whelen.com

Aviation

Installation Guide

Aviation model 90206 - ( )

Anti-Collision / Position Light Assembly

Form No.13390B (052206)

1.97

3.06

.51

9.375

10.63

26"

APPROX.

22"

APPROX.

3.75

WINGTIP SKIN

EXISTING

APPROX.

22"

MTG PLATE

SPECIFICATIONS (Position Light):

Nominal Operational Voltage: ...... 28 VDC

Average Input Current: ................. 1 AMP

Lamp for all Units:......................... 28VDC, 26 Watts Max.

EQUIPMENT LIMITATIONS:

An approved Anti-Collision / Position System consists of

two assemblies, one located on each wingtip.

INSTALLATION PROCEDURES:

The following information is to assist you in installing a

Whelen Anti-Collision / Position light system.

1. Choose the appropriate Model 90206 - ( ) replacement

light assembly.

2. The installation procedure described in the following

text will be confined to a single light installation, but is

identical for multiple light installation.

3. Remove old anti-collision light, locate and record

existing +28 VDC and (-) ground position and output

connector from power supply.

4. Use existing mounting holes and hardware.

5. Connect leads from light assembly in recorded

manner and lead from light to power supply.

6. Breaker

Requirements

Make sure existing system is equipped with an

appropriate sized breaker.

7. Install light assembly and insure that all leads are clear

of any obstructions and ty-rap as required. Secure

light assembly, use lock washers and/or thread lock,

on all threaded fasteners.

8. Check all avionics systems for interference from this

installation.

9. A flight check should be performed by a properly

certified pilot.

10. When necessary, waterproof the light assembly to

aircraft. Apply single part silicone (RTV) or equivalent

around any open area where water could get in.

11. Update aircraft records and complete Form 337.

12. Obtain FAA field approval for installation.

Model 90206 - ( )

Anti-Collision / Position

Light Assembly

FAA / TSO C30c TYPE 1,2 & 3

and

FAA / TSO - C96a

APPROVED

MADE IN THE U.S.A.

1 2 3

Aviation 1
WINGTIP SECTION 2

Summary of Contents

Page 1 - Aviation

Page 1®ENGINEERING COMPANY INC.Route 145, Winthrop Road,Chester, Connecticut 06412Phone: (860) 526-9504Fax: (860) 526-2009Internet: www.whelen.comSale

Page 2 - WINGTIP SECTION

Page 210/2/97CHG RET P/N'S18083ALIGHT ASSY, POS/ANTI-COLL - RIGHT (POL. RET)LIGHT ASSY, POS/ANTI-COLL - LEFT (POL. RET)--121201071311109876543211

Page 3

Page 3267C20054BAG HARDWARE3/27/98TO BE PACKAGED IN A PLASTIC BAGMS51957-33 (ITEM 26 - QTY 2)MS51959-32 (ITEM 7 - QTY 2)SCREWS:(ITEM 29) AND STAPLED T

Comments to this Manuals

No comments

Whelen 90206 User Manual Page 1

Browse online or download User Manual for Air equipment Whelen 90206. Whelen 90206 User Manual

Summary of Contents

Comments to this Manuals

Whelen 90206 User Manual Page 1

Browse online or download User Manual for Air equipment Whelen 90206. Whelen 90206 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Air equipment Whelen 90206